Product was successfully added to your shopping cart.
DSD TECH SH-HC-08 Bluetooth 4.0 BLE Slave Module to UART Transceiver for Arduino Compatible With IOS

DSD TECH SH-HC-08 Bluetooth 4.0 BLE Slave Module to UART Transceiver for Arduino Compatible With IOS

‎۳٬۰۵۲٬۵۰۰ ریال

(ناموجود)

قبلی

CC3-2405SF-E

قبلی

NRF51822-02 Data Transmission blue-tooth Module NORDIC BLE4.0 Low Power consumption

DSD TECH SH-HC-08 Bluetooth 4.0 BLE Slave Module to UART Transceiver for Arduino Compatible With IOS

برای نظر دادن به این محصول اولین باشید

بازنگری سریع

Technical Data:
TXD: serial transmit, 3.3V TTL level.
RXD: serial receiver, 3.3V TTL level.
CTS: serial flow control, is not supported.
RTS: serial flow control, is not supported.
DC: simulation, burning clock pin.
DD: simulation, data burning feet.
RST: reset pin module requires low level of not less than 5ms reset.
VCC: module power foot, requiring DC 3.3V power supply current is not less than 100mA.
GND: module common ground.
LED: LEDs module output pin, high output, series resistor connected LED.
Slave bright one second every two seconds. Once connected, LED lit.
KEY:. Input pin, internal pulldown This foot high, clear the record for the host address from the machine.
PIO: extended functionality for setting the module master-slave mode, the default internal pull-up resistor from the machine; external 1K pull-down resistor connected to ground, as the host. Currently only supports 9600bps communication, does not support the AT commands. Host, when pass-through traffic from the machine, there must be a certain time interval between packets. For example, the packet length is 500 bytes, then the transmission time interval between packets can be set to no less than 600ms. Otherwise, you may lose data.

دسترسی: ناموجود

اطلاعات اضافی

نام کالا DSD TECH SH-HC-08 Bluetooth 4.0 BLE Slave Module to UART Transceiver for Arduino Compatible With IOS
شرح کالا

Technical Data:
TXD: serial transmit, 3.3V TTL level.
RXD: serial receiver, 3.3V TTL level.
CTS: serial flow control, is not supported.
RTS: serial flow control, is not supported.
DC: simulation, burning clock pin.
DD: simulation, data burning feet.
RST: reset pin module requires low level of not less than 5ms reset.
VCC: module power foot, requiring DC 3.3V power supply current is not less than 100mA.
GND: module common ground.
LED: LEDs module output pin, high output, series resistor connected LED.
Slave bright one second every two seconds. Once connected, LED lit.
KEY:. Input pin, internal pulldown This foot high, clear the record for the host address from the machine.
PIO: extended functionality for setting the module master-slave mode, the default internal pull-up resistor from the machine; external 1K pull-down resistor connected to ground, as the host. Currently only supports 9600bps communication, does not support the AT commands. Host, when pass-through traffic from the machine, there must be a certain time interval between packets. For example, the packet length is 500 bytes, then the transmission time interval between packets can be set to no less than 600ms. Otherwise, you may lose data.

دیتاشیت

سازنده Abracon
اندازه ندارد
نوع کالا ماژول
MOQ 1

برچسب‌های محصول

برای جدا کردن برچسب‌ها از فاصله استفاده کنید. برای جملات نقل قول تکی (') را به کار ببرید.

  1. برای نظر دادن به این محصول اولین باشید

نظر خودتان را بنویسید

شما نظر می دهید: DSD TECH SH-HC-08 Bluetooth 4.0 BLE Slave Module to UART Transceiver for Arduino Compatible With IOS

شما به این محصول چه امتیازی می‌دهید؟ *

  1 ستاره 2 ستاره 3 ستاره 4 ستاره 5 ستاره
Quality
Value
Price
افرانیکی عزیز

سفارشاتی که تا 22 اسفند ثبت شوند، با تیپاکس و چاپار امکان ارسال دارند.

سفارشاتی که تا 26 اسفند ثبت شودن، با پست امکان ارسال دارند.

سفارشاتی که تا 27 اسفند ثبت شوند، با پیک و اسنپ امکان ارسال دارند.

سفارشاتی که از 28 اسفند تا 13 فروردین ثبت شوند، در 14 فروردین ارسال خواهند شد.