ماژول

DescriptionChip board ENC28J60/SS.The board 25MHZ crystal.The network interface board HR911105A.3.3V power supply pin.Size: 48.8 (mm) x 18.5 (mm).

DescriptionESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. Instruction & Steps of How to use:1. Download the Arduino IDE, the latest version. 2. Install the IDE3. Set up your Arduino IDE as: Go to File->Preferences and copy the URL below to get the ESP board…

description:This wireless transceiver module is an easy and suitable module if you want to setup your wireless communication system with low cost!! It can achieve a good balance between wireless transition performance and cost! You can easily add it with your own MCU/ARM/PIC/AVR/STM32 system! What\'s more, this NRF24L01+ module is designed with Power amplifier and SMA antenna. This allowed you to use the wireless communication up to 1000 meters! (No barrier)Frequence: 2.4GHz~2.5GHzOperating…

Description:Brand new and high quality.Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications.125 Channels, Multi-point communication and frequency hopping to meet the communication needs.Built-in hardware CRC error detection, Multipoint communication address control.Low-power 1.9 ~ 3.6V, only 1uA on Power down mode.Built-in 2.4Ghz antenna.Available software to set the address, only received local…

Description:Type : Voltage RegulatorCondition : NewApplication : ComputerSupply Voltage : 1Dissipation Power : 1Model Number : MWis_customized : YesWireless Module : SMD NRF24L01

Overview:Core51822 is a wireless module based on nRF51822 - the Multiprotocol Bluetooth® 4.0 low energy/2.4 GHz RF SoC designed for ULP (ultra low power) wirelesss applications.Core51822 SpecificationsOnboard chip: nRF51822Communication distance (open outdoor@1M data rate): 30mFrequency range: 2.4GHzOperating voltage: 2.0V ~ 3.6VOperating temperature: -40℃ ~ 85℃Dimension (PCB): 24.5mm x 32.26mmExpansion pinheader: all the I/Os except P0.26 and P0.27Pinheader pitch: 2.00mmSpacing between…

NRF51822-02 module is a data transmission module, the BLE Bluetooth MCU integrated SOC chip nRF51822-QAFF ,the internal integration of the underlying low power Bluetooth 4.0 standard protocol, module interface is the standard UART interface, built-in interrupt output prompt, When the module receives data from a pair of Bluetooth transmission, it outputs a high level signal, which is used to notify the external device, At the same time, the module is equipped with hardware.make enable foot,In…

Technical Data:TXD: serial transmit, 3.3V TTL level.RXD: serial receiver, 3.3V TTL level.CTS: serial flow control, is not supported.RTS: serial flow control, is not supported.DC: simulation, burning clock pin.DD: simulation, data burning feet.RST: reset pin module requires low level of not less than 5ms reset.VCC: module power foot, requiring DC 3.3V power supply current is not less than 100mA.GND: module common ground.LED: LEDs module output pin, high output, series resistor connected…

DescriptionConnect your Raspberry Pi to GSM/GPRS cell phone network with this shield. This Raspberry Pi GSM/GPRS shield lets you connect to the internet in the areas where is devoid of Wi-Fi or Ethernet. Quectel M66 module is the heart of this Raspberry Pi add-on. M66 is a quad-band GSM/GRPS module based on the latest 2G chipset which has the optimal performance in SMS & Data transmission and audio service even in harsh environment. You can plug a headset and make a call to someone…

Product Parameter:Support sampling rate (KHz): 8/11.025/12/16/22.05/24/32/44.1/48. Sound quality,stereophonic;24 bit DAC output, internal DSP hard decoding, non PWM output, dynamic range support 90dB,signal-to-noise ratio support 85dB;Fully support FAT16,FAT32 file system, support 32G TF Card,support 32G U disk;A variety of control mode, UART serial mode, serial port mode, AD button control mode;The broadcast language can be used to suspend the playing background music, support the song play…

RF TXRX MOD 2.4GHZ 802.11B/G/N

DC DC CONVERTER 0.9-6V 4W

Selling unit: Single article Individual package size: 3X4X5 cm Weight per unit:0.5 kg Type of packaging: standard package Ceramic GPS active reception antenna 12 * 12mm 12 L * 12 W * 6mm thick Gain 27DB, the equivalent of two to enlargeStability life, easy to damage. GPS active ceramic receiving antenna

(GPS-RTK2 BOARD - ZED-F9P (QWIIC

DC DC CONVERTER 5V 3W

DC DC CONVERTER 3.3V 3W

The active embedded patch antenna with circularly polarizedradiation pattern features directional operation to be used ina navigation scenario, where the antenna alwayskeep facing sky to receive satellite signals effectively.For different request of cable and connector, please contact us or our local distributors to have a customized solution.

1.27" FULL COLOR OLED GLASS

System-On-Modules - SOM System-On-Modules - SOM Zynq-7020, 1GB DDR3, 4GB eMMC

DC DC CONVERTER 0.8-6V

IC MODULE W5200+MAG JACK

ETHERNT 10/100 BASE-T/TX PHY MOD

IGBT MOD 1200V 20A 145W

Ebyte nRF51822 BLE 4.2 Low power E73-2G4M04S1D 2.4GHZ 4dBm RF Bluetooth Module

12*12*4mm namely PA012HAPI00 Patch Antenna On 13.4*12*0.5mm PCB With 30mm I-PEX Cable