Product was successfully added to your shopping cart.

ماژول

تنظیم جهت نزولی

   

آیتم‌های 1 تا 25 از مجموع 49 تا

  1. ۱
  2. ۲
مقایسه
تصویر
دیتا شیت
نام
توضیح کوتاه
سازنده
اندازه
قیمت
MOQ
سبد خرید
  1. (DS3231 AT24C32 IIC Module Precision Clock Module DS3231SN for Arduino Memory module (with battary

    Description
    The DS3231 is a low-cost, extremely accurate

    ...

    Description
    The DS3231 is a low-cost, extremely accurate I²C real-time clock (RTC) with an integrated temperature-compensated crystal oscillator (TCXO) and crystal. The device incorporates a battery input, and maintains accurate timekeeping when main power to the device is interrupted. The integration of the crystal resonator enhances the long-term accuracy of the device as well as reduces the piece-part count in a manufacturing line. The DS3231 is available in commercial and industrial temperature ranges, and is offered in a 16-pin, 300-mil SO package.
    The RTC maintains seconds, minutes, hours, day, date, month, and year information. The date at the end of the month is automatically adjusted for months with fewer than 31 days, including corrections for leap year. The clock operates in either the 24-hour or 12-hour format with an active-low AM/PM indicator. Two programmable time-of-day alarms and a programmable square-wave output are provided. Address and data are transferred serially through an I²C bidirectional bus.
    A precision temperature-compensated voltage reference and comparator circuit monitors the status of VCC to detect power failures, to provide a reset output, and to automatically switch to the backup supply when necessary. Additionally, the active-low RST pin is monitored as a pushbutton input for generating a µP reset.

    Features
    Accuracy ±2ppm from 0°C to +40°C
    Accuracy ±3.5ppm from -40°C to +85°C
    Battery Backup Input for Continuous Timekeeping
    Operating Temperature Ranges
    Commercial: 0°C to +70°C
    Industrial: -40°C to +85°C
    Low-Power Consumption
    Real-Time Clock Counts Seconds, Minutes, Hours, Day, Date, Month, and Year with Leap Year Compensation Valid Up to 2100
    Two Time-of-Day Alarms
    Programmable Square-Wave Output
    Fast (400kHz) I²C Interface
    3.3V Operation
    Digital Temp Sensor Output: ±3°C Accuracy
    Register for Aging Trim
    Active-Low RST Output/Pushbutton Reset Debounce Input



    China
    ندارد
    ‎۵۰۰٬۵۰۰ ریال
    ۱
  2. (ESP32-WROOM-32U (16MB

    WiFi Modules (802.11) SMD Module, ESP32-D0WD, 128Mbits SPI flash, UART mode, U.FL antenna connector

    Abracon
    ندارد
    ‎۳٬۳۶۸٬۸۰۰ ریال از: ‎۳٬۳۴۱٬۳۰۰ ریال
    ۱
  3. (SIM868(24M

    SIM868 module is a complete Quad-Band GSM/GPRS module which combines GNSS technology for satellite n

    ... SIM868 module is a complete Quad-Band GSM/GPRS module which combines GNSS technology for satellite navigation 24M


    SIMCom
    ندارد
    ‎۳٬۸۱۵٬۶۰۰ ریال از: ‎۳٬۷۱۲٬۵۰۰ ریال
    ۱
  4. (SIM868(32M

    SIM868 module is a complete Quad-Band GSM/GPRS module which combines GNSS technology for satellite n

    ... SIM868 module is a complete Quad-Band GSM/GPRS module which combines GNSS technology for satellite navigation 32M


    SIMCom
    ندارد
    ‎۴٬۶۰۶٬۳۰۰ ریال از: ‎۴٬۵۶۵٬۰۰۰ ریال
    ۱
  5. 2.4g Nrf24l01 PA LNA SMA Antenna Wireless Transceiver Communication Module

    description:
    This wireless transceiver module is an easy

    ...

    description:
    This wireless transceiver module is an easy and suitable module if you want to setup your wireless communication system with low cost!! It can achieve a good balance between wireless transition performance and cost! You can easily add it with your own MCU/ARM/PIC/AVR/STM32 system! What\'s more, this NRF24L01+ module is designed with Power amplifier and SMA antenna. This allowed you to use the wireless communication up to 1000 meters! (No barrier)
    Frequence: 2.4GHz~2.5GHz
    Operating voltage: 3 ~ 3.6V Max
    Current: 115mA
    Multi-frequency: 125 frequency
    Support up to six channels of data reception
    Communication distance: up to 1000 meters (No barrier)



    China
    ندارد
    ‎۹۱۱٬۶۰۰ ریال
    ۱
  6. 317990027

    Interface Development Tools PL2303 USB to Serial (TTL) Module&Adapter

    Seeed Studio
    ندارد
    ‎۷۵۰٬۸۰۰ ریال از: ‎۷۳۵٬۷۰۰ ریال
    ۱
  7. AMW007-1.2.0R

    RF TXRX MOD 2.4GHZ 802.11B/G/N

    Silicon Labs
    ندارد
    ‎۲٬۳۲۳٬۸۰۰ ریال
    ۱
  8. Arduino compatible development board with Nano-based microcontroller USB serial converter ATmega328P and CH340

    Description:
    Arduino NANO with ATmega32

    ...

    Description:
    Arduino NANO with ATmega328 Microcontroller is an ultra-low size Arduino board with AVR architecture and based on Atmel Atmega328P-AU microcontroller, which includes all capabilities of Arduino Duemilanove except DC power jack in the smallest size.
    This miniature board is like an Arduino UNO type, but with a smaller size, which is suitable for a flyer and tiny robot. This Arduino is idealized for breadboard working too.
    The Arduino NANO is equipped with 8 pins for analog inputs (to run 10-bit resolution means 1024 different values), and 14 digital IO pins that 6 pins can be used for PWM outputs, 2pins for serial receive and transmit data, 2pins for external interrupts, 4pins for SPI serial ports, and on for LED indicator. It also has a pin for reference voltage input for analog reference comparison and one pin for reset the microcontroller.
    This Arduino chip operates with a TTL logic level of 3.3V DC and can be supplied with a recommended voltage of 7V to 9V DC. It can easily be supplied through a micro-USB to USB cable from any USB port or through the AC to DC or a 9V battery. It is also compatible with 1.0 Arduino pinout and any shields with 3.3V DC.
    Arduino NANO can withstand maximum input and output voltage of 3.3V, which means that applying more than 3.3V DC to any input or output pins may damage the board. This board has all the requirements of the microcontroller support.
    Arduino is an open-source platform based on simple userfriendly hardware and software.
    The Arduino board can be employed as a slave operator, that performs simple digit works based on instructions.

    Features:
    Microcontroller: ATmega328
    Architecture: AVR
    Operating Voltage: 5 V
    Flash Memory: 32 KB of which 2 KB used by bootloader
    SRAM: 2 KB
    Clock Speed: 16 MHz
    Analog IN Pins: 8
    EEPROM: 1 KB
    DC Current per I/O Pins: 40 mA (I/O Pins)
    Input Voltage: 7~9 V MAX
    Digital I/O Pins: 22 (6 of which are PWM)
    PWM Output: 6
    Power Consumption: 19 mA
    PCB Size: 18mm x 45 mm



    ARDUINO
    ندارد
    ‎۹۳۵٬۰۰۰ ریال از: ‎۹۰۷٬۵۰۰ ریال
    ۱
  9. ARDUINO DEVELOPMENT BOARD

    arduino development bord Treedix 2pcs ATmega328P CH340 Development Boar

    ...

    arduino development bord Treedix 2pcs ATmega328P CH340 Development Board Compatible with Arduino UNO R3 Board Kit for Starter

    The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3. This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit. Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!



    China
    ندارد
    ‎۴٬۹۷۷٬۵۰۰ ریال از: ‎۴٬۹۵۰٬۰۰۰ ریال
    ۱
  10. BGM13P32F512GE-V2

    Bluetooth Modules (802.15.1) BGM13P32F512GE Bluetooth module Supports high-throughput, long range, a

    ... Bluetooth Modules (802.15.1) BGM13P32F512GE Bluetooth module Supports high-throughput, long range, and regular Bluetooth LE PHYs


    Silicon Labs
    ندارد
    ‎۶٬۰۹۹٬۱۰۰ ریال
    ۱
  11. CH340G

    USB to Serial TTL - RS232 converter IC - SOIC16

    Abracon
    16-SOIC
    ‎۱٬۰۷۲٬۵۰۰ ریال
    ۱
  12. DIYmall 2pcs Hx711 Weight Weighing Load Cell Conversion Module Sensors Ad Module for Arduino Microcontroller

    Product description
    Package contents:
    1 x Load cell

    ...

    Product description
    Package contents:
    1 x Load cell 0-5KG
    1 x HX711 24BIT Precision ADC Module on breakout board
    10 x Breakaway header pins for HX711 connection
    Everything you need to take accurate force measurements with and Arduino, Raspberry Pi, or other microcontroller in one complete package!

    Information:
    Load cell - Sturdy aluminum alloy construction. Strain gauges pre-attached with strain relieved wires. Accurately measures forces from 0-5kg (0-11 lb).
    HX711 - This top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any microcontroller (like an Arduino or Raspberry Pi).
    Load cell specs:
    -Wire leads pre-attached, 22 cm (8.5 in) long
    -Dimensions 12.7 mm high, 12.7 mm wide, 80 mm long (0.5 in x 0.5 in x 3.15 in)
    -4 mounting holes, 15 mm spacing on each side. One side both holes tapped M4 thread, the other side both holes tapped M5 thread.

    HX711 specs:
    -Operation Voltage: 2.7V–5V
    -Operation Current: < 1.5mA
    -Mounted on breakout board
    -Includes breakaway headers for connection, soldering required

    Connections:
    Red to E+
    Black to E-
    Green to A+
    White to A-



    Degraw
    ندارد
    ‎۸۴۰٬۱۰۰ ریال
    ۱
  13. DSD TECH SH-HC-08 Bluetooth 4.0 BLE Slave Module to UART Transceiver for Arduino Compatible With IOS

    Technical Data:
    TXD: serial transmit, 3.3V TTL level.

    ...

    Technical Data:
    TXD: serial transmit, 3.3V TTL level.
    RXD: serial receiver, 3.3V TTL level.
    CTS: serial flow control, is not supported.
    RTS: serial flow control, is not supported.
    DC: simulation, burning clock pin.
    DD: simulation, data burning feet.
    RST: reset pin module requires low level of not less than 5ms reset.
    VCC: module power foot, requiring DC 3.3V power supply current is not less than 100mA.
    GND: module common ground.
    LED: LEDs module output pin, high output, series resistor connected LED.
    Slave bright one second every two seconds. Once connected, LED lit.
    KEY:. Input pin, internal pulldown This foot high, clear the record for the host address from the machine.
    PIO: extended functionality for setting the module master-slave mode, the default internal pull-up resistor from the machine; external 1K pull-down resistor connected to ground, as the host. Currently only supports 9600bps communication, does not support the AT commands. Host, when pass-through traffic from the machine, there must be a certain time interval between packets. For example, the packet length is 500 bytes, then the transmission time interval between packets can be set to no less than 600ms. Otherwise, you may lose data.



    Abracon
    ندارد
    ‎۳٬۰۵۲٬۵۰۰ ریال
    ۱
  14. E73-2G4M04S1D

    Ebyte nRF51822 BLE 4.2 Low power E73-2G4M04S1D 2.4GHZ 4dBm RF Bluetooth Module

    EBYTE
    SMD
    ‎۱٬۵۱۹٬۳۰۰ ریال
    ۱
  15. ENC28J60

    Ethernet LAN Network Module for Arduino SPI AVR PIC LPC STM32

    Microchip Technology
    ندارد
    ‎۲٬۰۲۱٬۳۰۰ ریال
    ۱
  16. ESP-12E

    ESP8266 ESP-12F Serial WIFI Model ESP-12E Upgrade Remote Wireless WIFI Module ESP12F ESP12

    China
    ندارد
    ‎۷۷۰٬۰۰۰ ریال از: ‎۷۵۶٬۳۰۰ ریال
    ۱
  17. ESP-WROOM-32 (4MB)

    WiFi Modules (802.11) SMD Module, ESP32-D0WD, 32Mbits 4Mb SPI Flash, UART mode, U.fl Ant Connector

    China
    ندارد
    ‎۱٬۶۵۰٬۰۰۰ ریال
    ۱
  18. esp32-cam

    Features: - Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module

    ...

    Features: - Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module - Low-power dual-core 32-bit CPU for application processors - Up to 240MHz, up to 600 DMIPS - Built-in 520 KB SRAM, external 4M PSRAM - Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC - Support OV2640 and OV7670 cameras with built-in flash - Support for WiFI upload -Support TF card - Support multiple sleep modes - Embedded Lwip and FreeRTOS - Support STA/AP/STA+AP working mode - Support Smart Config/AirKiss One-click distribution network - Support for serial local upgrade and remote firmware upgrade (FOTA) Description: CES NEWS' Geekcreit ESP32-CAM WiFi + Bluetooth Camera Module Development Board ESP32 With Camera Module OV2640 2MP - Board & Shield Motherboard & Development Board. The ESP32-CAM has a very competitive small-size camera module that can operate independently as a minimum system, measuring the only 27*40.5*4.5mm, with deep sleep current and a minimum of 6mA. ESP-32CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals and other IoT applications. It is an solution for IoT applications. ESP-32CAM is packaged in and can be directly plugged into the backplane for quick production. It provides customers with a highly reliable connection method and is convenient for use in various IoT hardware terminals. Note: This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately. Package Included: 1 x ESP32-CAM Module 1 x Camera Module OV2640 2MP Product Specifications: ESP32-CAM Picture Output Format Rate: Test environment: camera model: OV2640 XCLK: 20



    China
    ندارد
    ‎۲٬۵۰۲٬۵۰۰ ریال
    ۱
  19. ESP32-D0WDQ6

    RF System on a Chip - SoC SMD IC ESP32-D0WDQ6, Dual Core MCU, WiFi & Bluetooth Combo, QFN48-pin, 6*6

    ... RF System on a Chip - SoC SMD IC ESP32-D0WDQ6, Dual Core MCU, WiFi & Bluetooth Combo, QFN48-pin, 6*6mm


    Espressif Systems
    ندارد
    ‎۹۹۰٬۰۰۰ ریال از: ‎۹۷۶٬۳۰۰ ریال
    ۱
  20. ESP32-S3-WROOM-1

    About this item 32 bit MCU, 2.4 GHz Wi­Fi + Bluetooth LE SoC Suppor

    ...

    About this item 32 bit MCU, 2.4 GHz Wi­Fi + Bluetooth LE SoC Supporting IEEE 802.11 b/g/n and Bluetooth 5 Based on ESP32-S3-WROOM-1 8MB Flash + 2 MB PSRAM About ESP32-S3 hardware resources ESP32-S3 is a low-power MCU-based SoC that supports 2.4 GHz Wi-Fi and Bluetooth Low Energy (Bluetooth LE). ESP32-S3 has a complete Wi-Fi subsystem and a Bluetooth LE subsystem, State-of-the-art power and RF performance. S3 provides a rich set of peripheral interfaces, and supports ultra-low-powerapplications. Different security features allow the device to meet stringent security requirements. Instructions for using the USB cable The on-board USB port of the YD-ESP32-S3 core board is the Type-C interface.It can communicate with the computer and provide power. The cable can be used: USB Type A to Type-C cable or CC cable Note the distinction between the commonly used USB A port to Type-C cable that can only be charged, which cannot be used for communication between YD-ESP32-S3 and the host.



    China
    ندارد
    ‎۲٬۵۱۹٬۰۰۰ ریال از: ‎۲٬۴۷۵٬۰۰۰ ریال
    ۱
  21. ESP32-WROOM-32

    WiFi Modules (802.11) Module 4 MB Flash ESP32-D0WDQ6

    Espressif Systems
    ندارد
    ‎۱٬۸۸۳٬۸۰۰ ریال از: ‎۱٬۸۵۶٬۳۰۰ ریال
    ۱
  22. ESP32-WROOM-32D

    WiFi Modules (802.11) SMD Module, ESP32-D0WD, 32Mbits SPI flash, UART mode, PCB antenna

    Espressif Systems
    ندارد
    ‎۱٬۵۹۰٬۸۰۰ ریال از: ‎۱٬۵۵۵٬۱۰۰ ریال
    ۱
  23. ESP8266 ESP-01 Serial WIFI Wireless Transceiver Module Send Receive LWIP AP+STA

    Overview:
    This is WiFi serial transceiver module, based

    ...

    Overview:
    This is WiFi serial transceiver module, based on ESP8266 SoC.
    The SOC has Integrated TCP/IP protocol stack
    We have a set of documents in Chinese. We are preparing tutorials and demo software to showcase utility of this module.
    ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
    ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.

    Corresponding Interface:
    SDIO 2.0, SPI, UART
    32-pin QFN package
    Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
    Integrated RISC processor, on-chip memory and external memory interfaces
    Integrated MAC/baseband processors
    Quality of Service management
    I2S interface for high fidelity audio applications
    On-chip low-dropout linear regulators for all internal supplies
    Proprietary spurious-free clock generation architecture
    Integrated WEP, TKIP, AES, and WAPI engines

    Specification:
    802.11 b/g/n
    Wi-Fi Direct (P2P), soft-AP
    Integrated TCP/IP protocol stack
    Integrated TR switch, balun, LNA, power amplifier and matching network
    Integrated PLLs, regulators, DCXO and power management units
    +19.5dBm output power in 802.11b mode
    Power down leakage current of <10uA
    Integrated low power 32-bit CPU could be used as application processor
    SDIO 1.1/2.0, SPI, UART
    STBC, 1×1 MIMO, 2×1 MIMO
    A-MPDU & A-MSDU aggregation & 0.4ms guard interval
    Wake up and transmit packets in < 2ms
    Standby power consumption of < 1.0mW (DTIM3)



    China
    ندارد
    ‎۷۵۰٬۸۰۰ ریال
    ۱
  24. ESP8266 ESP-03 Serial Wifi Wireless Transceiver Module Send Receiver LWIP AP+STA

    Description
    1. Support 802.11 B/G/N
    2. Communicat

    ...

    Description
    1. Support 802.11 B/G/N
    2. Communication range up to 100 yards depending on environment.
    3. Standard 3.3VDC operation with 5V compatible I/O.
    4. Standard 3 wire (TXD/RXD/GND) serial communication (idle high) at 115200/8/N/1.
    5. Standard 0.1" (2.54mm) half through hole.
    6. Upgradeable firmware.
    7. Three mode of operations: Client/Access Point/Both Client and Access Point.
    8. Support all major security schemes: OPEN/WEP/WPA_PSK/WPA2_PSK/WPA_WPA2_PSK.
    9. Support both TCP and UDP communication.
    10. Working as TCP/UPD server supports up to five (5) connections.
    11. Working as station can connect up to 5 TCP/UPD servers. The ESP-04 can connect to all standard non-SSL websites in the world.
    12. Simple AT commands for all operations.
    13. Connection based data reception or transparent data reception.
    14. Programmable client connection inactivity timeout.
    15. Automatic domain name address resolution for public domain name but not the local name within the local area network (router).



    China
    ندارد
    ‎۱٬۲۳۳٬۳۰۰ ریال
    ۱
  25. ESP8266 ESP-07 Serial WIFI Wireless Transceiver Wireless Module LWIP AP+STA

    Description:
    1X(The ESP8266 is a chip highly designed fo

    ...

    Description:
    1X(The ESP8266 is a chip highly designed for the needs of a new connected world.
    It offers a complete and self-contained Wi-Fi network solution, allowing you to either host the application or download all Wi-Fi network functions from another application processor.
    Its high degree of integration on the chip allows minimal external circuitry, and the complete solution, including the input section module, is designed to occupy a minimum area of PCB.
    Dimensions: 4 x 3 x 0.3 cm
    Color: Blue; 100% New and high quality. This product is your best choice. Do not hesitate. It is time to replace your old, worn, damaged product.
    Materials: CCL
    Warnings:
    This module requires a voltage supply of 3.3 for VCC, and 3.3V of logic.
    Can not accept 5V.
    Connecting the RX or TX over 5V Arduino will destroy this module.
    You must use a logic level converter, or a 3.3V for Arduino
    The supply of 3.3V on the Arduino Uno has an inadequate current capacity to power this module.
    It must provide a separate power supply and higher than 3.3V (approximately 300mA or better)
    Package includes:
    1 x Wireless WiFi Remote Transducer Module ESP8266 Serial Esp-07 LWIP AP + STA
    Only the above package content, other products are not included.
    Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.)



    China
    ندارد
    ‎۱٬۱۶۱٬۸۰۰ ریال
    ۱
تنظیم جهت نزولی

   

آیتم‌های 1 تا 25 از مجموع 49 تا

  1. ۱
  2. ۲
افرانیکی عزیز

سفارشاتی که تا 22 اسفند ثبت شوند، با تیپاکس و چاپار امکان ارسال دارند.

سفارشاتی که تا 26 اسفند ثبت شودن، با پست امکان ارسال دارند.

سفارشاتی که تا 27 اسفند ثبت شوند، با پیک و اسنپ امکان ارسال دارند.

سفارشاتی که از 28 اسفند تا 13 فروردین ثبت شوند، در 14 فروردین ارسال خواهند شد.