ماژول

Overview:
This is WiFi serial transceiver module, based on ESP8266 SoC.
The SOC has Integrated TCP/IP protocol stack
We have a set of documents in Chinese. We are preparing tutorials and demo software to showcase utility of this module.
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.

Corresponding Interface:
SDIO 2.0, SPI, UART
32-pin QFN package
Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
Integrated RISC processor, on-chip memory and external memory interfaces
Integrated MAC/baseband processors
Quality of Service management
I2S interface for high fidelity audio applications
On-chip low-dropout linear regulators for all internal supplies
Proprietary spurious-free clock generation architecture
Integrated WEP, TKIP, AES, and WAPI engines

Specification:
802.11 b/g/n
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Integrated TR switch, balun, LNA, power amplifier and matching network
Integrated PLLs, regulators, DCXO and power management units
+19.5dBm output power in 802.11b mode
Power down leakage current of <10uA
Integrated low power 32-bit CPU could be used as application processor
SDIO 1.1/2.0, SPI, UART
STBC, 1×1 MIMO, 2×1 MIMO
A-MPDU & A-MSDU aggregation & 0.4ms guard interval
Wake up and transmit packets in < 2ms
Standby power consumption of < 1.0mW (DTIM3)

Description
1. Support 802.11 B/G/N
2. Communication range up to 100 yards depending on environment.
3. Standard 3.3VDC operation with 5V compatible I/O.
4. Standard 3 wire (TXD/RXD/GND) serial communication (idle high) at 115200/8/N/1.
5. Standard 0.1" (2.54mm) half through hole.
6. Upgradeable firmware.
7. Three mode of operations: Client/Access Point/Both Client and Access Point.
8. Support all major security schemes: OPEN/WEP/WPA_PSK/WPA2_PSK/WPA_WPA2_PSK.
9. Support both TCP and UDP communication.
10. Working as TCP/UPD server supports up to five (5) connections.
11. Working as station can connect up to 5 TCP/UPD servers. The ESP-04 can connect to all standard non-SSL websites in the world.
12. Simple AT commands for all operations.
13. Connection based data reception or transparent data reception.
14. Programmable client connection inactivity timeout.
15. Automatic domain name address resolution for public domain name but not the local name within the local area network (router).

Description:
1X(The ESP8266 is a chip highly designed for the needs of a new connected world.
It offers a complete and self-contained Wi-Fi network solution, allowing you to either host the application or download all Wi-Fi network functions from another application processor.
Its high degree of integration on the chip allows minimal external circuitry, and the complete solution, including the input section module, is designed to occupy a minimum area of PCB.
Dimensions: 4 x 3 x 0.3 cm
Color: Blue; 100% New and high quality. This product is your best choice. Do not hesitate. It is time to replace your old, worn, damaged product.
Materials: CCL
Warnings:
This module requires a voltage supply of 3.3 for VCC, and 3.3V of logic.
Can not accept 5V.
Connecting the RX or TX over 5V Arduino will destroy this module.
You must use a logic level converter, or a 3.3V for Arduino
The supply of 3.3V on the Arduino Uno has an inadequate current capacity to power this module.
It must provide a separate power supply and higher than 3.3V (approximately 300mA or better)
Package includes:
1 x Wireless WiFi Remote Transducer Module ESP8266 Serial Esp-07 LWIP AP + STA
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.)

Features:
SDIO 2.0, SPI, UART , 32-pin QFN package , Integrated RF switch, balun, 24dBm PA, DCXO, and PMU , Integrated RISC processor, on-chip memory and external memory interfaces , Integrated MAC/baseband processors , Quality of Service management
I2S interface for high fidelity audio applications , On-chip low-dropout linear regulators for all internal supplies , Proprietary spurious-free clock generation architecture , Integrated WEP, TKIP, AES, and WAPI engines Solutions
Specifications: 802.11 b/g/n , Wi-Fi Direct (P2P), soft-AP , Integrated TCP/IP protocol stack , Integrated TR switch, balun, LNA, power amplifier and matching network , Integrated PLLs, regulators, DCXO and power management units , +19.5dBm output power in 802.11b mode
Power down leakage current of <10uA , Integrated low power 32-bit CPU could be used as application processor , SDIO 1.1/2.0, SPI, UART , STBC, 1?1 MIMO, 2?1 MIMO , A-MPDU & A-MSDU aggregation & 0.4ms guard interval , Wake up and transmit packets in < 2ms , Standby power consumption of < 1.0mW (DTIM3)

Description:
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. , ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.

Overview:
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.

Description:
Breakthrough design, there are new breakthroughs, based on ESP-12E.
The new four-layer board design.
The new revision antenna RF performance optimization, communication distance is increased by 30% -50% compared to ESP-12E!
Semi-hole chip technology, the whole IO leads, with metal shielding shell
Passed FCC & CE & RoHS certification
Built-board PCB antenna
4M bytes SPI Flash for programming.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.

Features:
Standards Certification: FCC / CE / TELEC
Wireless standards: 802.11 b / g / n
Frequency range: 2.4GHz-2.5GHz (2400M-2483.5M)
Data interface: UART / HSPI / I2C / I2S / Ir Remote Contorl GPIO / PWM
Operating voltage: 3.0 ~ 3.6V (recommendation 3.3V)
Working Current: Average: 80mA
Operating temperature: -40 ° ~ 125 °
Storage temperature: Nomal temperatu

Selling unit: Single article Individual package size: 3X4X5 cm Weight per unit:0.5 kg Type of packaging: standard package Ceramic GPS active reception antenna 12 * 12mm 12 L * 12 W * 6mm thick Gain 27DB, the equivalent of two to enlargeStability life, easy to damage. GPS active ceramic receiving antenna

Description The HC-12 is a 100mW multi-channel wireless transceiver you can use in your projects to transmit and receive serial information. The HC-12 is a half-duplex wireless serial communication module with 100 channels in the 433.4-473.0 MHz range that is capable of transmitting up to 1 km. This project will begin by using the HC-12 to create a wireless link between two computers and end with a second article that creates a simple wireless GPS tracker.

Overview:
Core51822 is a wireless module based on nRF51822 - the Multiprotocol Bluetooth® 4.0 low energy/2.4 GHz RF SoC designed for ULP (ultra low power) wirelesss applications.
Core51822 Specifications
Onboard chip: nRF51822
Communication distance (open outdoor@1M data rate): 30m
Frequency range: 2.4GHz
Operating voltage: 2.0V ~ 3.6V
Operating temperature: -40℃ ~ 85℃
Dimension (PCB): 24.5mm x 32.26mm
Expansion pinheader: all the I/Os except P0.26 and P0.27
Pinheader pitch: 2.00mm
Spacing between pinheaders on the left side and the right side: 18.00mm
Antenna: onboard antenna
NRF51822 Features:
2.4 GHz multiprotocol RF transceiver
ARM® Cortex™-M0 32 bit processor
128 bit AES HW encryption
128kB flash & 16Kb RAM
Programmable Peripheral Interconnect (PPI)
Digital interfaces: SPI, I2C, UART
10 bit ADC
Programmable output power: -20 to +4 dBm
Independent application development and protocol stack
Fully compatible with NRF24L series
Pinout compatible with NRF51xxx series
Global separate power management
Operating voltage: 1.8 V ~ 3.6 V
Applications:
Wearable devices
Bluetooth intelligent application
Mobile phone accessories
RFID labels
Smart home appliances
Industry control
Data acquisition system
Revision History
2015.06, Core51822 upgrades the onboard chip to Rev3, features RAM 16K,
supports higher version SDK, and all the demo codes are still compatible with the Rev2 ones.
Package Include:
1 x Low Power Consumption BLE4.0 Bluetooth 2.4 GHz Wireless Module NRF51822

Brand new and high quality. Chip board ENC28J60-I/SO. The board 25MHZ crystal. The network interface board HR911105A. 3.3 V supply pin. Debug reminder: 1, the IP address of the computer to a network segment and module such as IP module 192.168.1.2, IP computer set: 192.168.1.3; 192.168.1 is the 3 section; 2, the network cable connected to the mouth of the computer network module and mouth; (that is, the cable network 1 3,2 , and then do not understand that there are pictures Baidu); 3, the module and the MCU connection should pay attention to the connection of each line is reliable (the surface is not even connected to the good); 4, and the MCU port IO to confirm that is right; 5, the program recompile, download, confirm whether to download! STM32 and 51 IO size:48 x 18mm Material:plastic colour:blue Package Contents: 1 x Ethernet Shield Only the above package content, other products are not included. Note: Light and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

Description
Chip board ENC28J60/SS.
The board 25MHZ crystal.
The network interface board HR911105A.
3.3V power supply pin.
Size: 48.8 (mm) x 18.5 (mm).

Size: 18*18*2.8 (±0.2)mm- SPI Flash: 1MB-The type of interface: UART/GPIO/ADC/PWM-The quantity of IO put: 11 Series rate: 300-4608000 bps, the default is 115200bps-RF range: 2412-2484MHz-RF range: 2412-2484MHz The type of antenna: onboard PCB wire Transmission power: 802.11b: 16±2 dB (@11Mbps) 802.11g: 14±2 dB (@54Mbps) 802.11n: 13±2 dB (@HT20, MCS7) Receiving sensitivity: CCK, 1Mbps: -90dB CCK, 11Mbps: -85dB 6 Mbps (1/2 BPSK): -88dBm 54 Mbps (3/4 64-QAM): -70dBm HT20, MCS7 (65 Mbps, 72.2 Mbps): -67dBm Power consumption: Continuous transmission→average value:71 mA, maximum value: 300 mA. Modem sleep: 20mA Light sleep: 2mA Deep sleep: 0.02mA Security: WEP/WPA-PSK/WPA2-PSK-Supply voltage: 3.0V-3.6V-Supply current: >300mA

Product Parameter:
Support sampling rate (KHz): 8/11.025/12/16/22.05/24/32/44.1/48. Sound quality,stereophonic;
24 bit DAC output, internal DSP hard decoding, non PWM output, dynamic range support 90dB,signal-to-noise ratio support 85dB;
Fully support FAT16,FAT32 file system, support 32G TF Card,support 32G U disk;
A variety of control mode, UART serial mode, serial port mode, AD button control mode;
The broadcast language can be used to suspend the playing background music, support the song play under the specified path, support the cross disc sowing, and support the early end of the broadcast;
Specify time to play;
Specify a disc play, and a specified repertoire is played 30 level volume adjustable, 5 EQ adjustable.（NORMAL—POP—ROCK—JAZZ--CLASSIC）;
Specify a path to play (in support of Chinese and English);
Folder switching;
Specified time period;
Supports computer sound card control and USB mass storage;
Supporting triggers cannot interrupt playback;
Introduction:
N9200B is a MP3 chip that provides serial port,which perfectly integrates MP3 and WMV hard decoder chips.
It includes the N9200A and N9200B Music MP3modules,and the software supports TF driver, supports the computer to update the content of SPI-flash directly, and supports the FAT16 and FAT32 file systems.
Through a simple UART serial command or a first-line serial port instruction to play the specified music, and how to play music and other functions, without the tedious underlying operation, good sound quality, easy to use, stable and reliable is the biggest feature of this product.
In addition, the chip is also a product of deep customization, which is a low-cost solution for fixed voice playback.

Description
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.

Instruction & Steps of How to use:
1. Download the Arduino IDE, the latest version.
2. Install the IDE
3. Set up your Arduino IDE as: Go to File->Preferences and copy the URL below to get the ESP board manager extensions: http://arduino.esp8266.com/stable/package_esp8266com_index.json Placing the http:// before the URL lets the Arduino IDE use it...otherwise it gives you a protocol error.
4. Go to Tools > Board > Board Manager> Type "esp8266" and download the Community esp8266 and install.
5. Set up your chip as:
Tools -> Board -> NodeMCU 1.0 (ESP-12E Module)
Tools -> Flash Size -> 4M (3M SPIFFS)
Tools -> CPU Frequency -> 80 Mhz
Tools -> Upload Speed -> 921600
Tools-->Port--> (whatever it is)
6. Download and run the 32 bit flasher exe at Github(Search for nodemcu/nodemcu-flasher/tree/master/ at Github)
github.com/nodemcu/nodemcu-flasher/tree/master/Win32/Release
Or download and run the 64 bit flasher exe at:
github.com/nodemcu/nodemcu-flasher/tree/master/Win64/Release
7. In Arduino IDE, look for the old fashioned Blink program. Load, compile and upload.
8. Go to FILE> EXAMPLES> ESP8266> BLINK, it will start blinking.

This module uses the newest 2.4ghz transceiver from Nordic Semiconductor, the nrf24l01+. It integrates a complete 2.4ghz RF transceiver, RF synthesizer, and baseband logic including the Enhanced shockburst™ hardware protocol accelerator supporting a high-speed SPI interface for the application controller. The ‘+’ version of the IC has improved range, sensitivity, and data rates. The command set is backward compatible with the original nrf24l01.Worldwide 2.4GHz ISM band operation 250kbps, 1Mbps and 2Mbps on air data rates Ultra low power operation Power supply : 1.9~3.6V Dimension : 12x18mm

Description:
Brand new and high quality.
Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications.
125 Channels, Multi-point communication and frequency hopping to meet the communication needs.
Built-in hardware CRC error detection, Multipoint communication address control.
Low-power 1.9 ~ 3.6V, only 1uA on Power down mode.
Built-in 2.4Ghz antenna.
Available software to set the address, only received local Address when output data(Provide interrupt instruction), can be directly connected to a variety of microcontrollers, Software programming is very convenient.
Built-in voltage regulator.
Standard DIP Pitch Interface for embedded applications.
Size:3.3cm x 1.4cm - 1.29inch x 0.56inch.
Package Includes:
1pc NRF24L01+ Wireless Transceiver Module