WiFi Modules (802.11) SMD Module, ESP32-D0WD, 32Mbits 4Mb SPI Flash, UART mode, U.fl Ant Connector
Features: - Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
Features: - Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module - Low-power dual-core 32-bit CPU for application processors - Up to 240MHz, up to 600 DMIPS - Built-in 520 KB SRAM, external 4M PSRAM - Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC - Support OV2640 and OV7670 cameras with built-in flash - Support for WiFI upload -Support TF card - Support multiple sleep modes - Embedded Lwip and FreeRTOS - Support STA/AP/STA+AP working mode - Support Smart Config/AirKiss One-click distribution network - Support for serial local upgrade and remote firmware upgrade (FOTA) Description: CES NEWS' Geekcreit ESP32-CAM WiFi + Bluetooth Camera Module Development Board ESP32 With Camera Module OV2640 2MP - Board & Shield Motherboard & Development Board. The ESP32-CAM has a very competitive small-size camera module that can operate independently as a minimum system, measuring the only 27*40.5*4.5mm, with deep sleep current and a minimum of 6mA. ESP-32CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals and other IoT applications. It is an solution for IoT applications. ESP-32CAM is packaged in and can be directly plugged into the backplane for quick production. It provides customers with a highly reliable connection method and is convenient for use in various IoT hardware terminals. Note: This product contains the OV2640 Camera Module. If you need to use the OV7670 camera, please purchase it separately. Package Included: 1 x ESP32-CAM Module 1 x Camera Module OV2640 2MP Product Specifications: ESP32-CAM Picture Output Format Rate: Test environment: camera model: OV2640 XCLK: 20
RF System on a Chip - SoC SMD IC ESP32-D0WDQ6, Dual Core MCU, WiFi & Bluetooth Combo, QFN48-pin, 6*6
About this item 32 bit MCU, 2.4 GHz WiFi + Bluetooth LE SoC Suppor
About this item 32 bit MCU, 2.4 GHz WiFi + Bluetooth LE SoC Supporting IEEE 802.11 b/g/n and Bluetooth 5 Based on ESP32-S3-WROOM-1 8MB Flash + 2 MB PSRAM About ESP32-S3 hardware resources ESP32-S3 is a low-power MCU-based SoC that supports 2.4 GHz Wi-Fi and Bluetooth Low Energy (Bluetooth LE). ESP32-S3 has a complete Wi-Fi subsystem and a Bluetooth LE subsystem, State-of-the-art power and RF performance. S3 provides a rich set of peripheral interfaces, and supports ultra-low-powerapplications. Different security features allow the device to meet stringent security requirements. Instructions for using the USB cable The on-board USB port of the YD-ESP32-S3 core board is the Type-C interface.It can communicate with the computer and provide power. The cable can be used: USB Type A to Type-C cable or CC cable Note the distinction between the commonly used USB A port to Type-C cable that can only be charged, which cannot be used for communication between YD-ESP32-S3 and the host.
WiFi Modules (802.11) Module 4 MB Flash ESP32-D0WDQ6
WiFi Modules (802.11) SMD Module, ESP32-D0WD, 32Mbits SPI flash, UART mode, PCB antenna
Overview:
This is WiFi serial transceiver module, based
Overview:
This is WiFi serial transceiver module, based on ESP8266 SoC.
The SOC has Integrated TCP/IP protocol stack
We have a set of documents in Chinese. We are preparing tutorials and demo software to showcase utility of this module.
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.
Corresponding Interface:
SDIO 2.0, SPI, UART
32-pin QFN package
Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
Integrated RISC processor, on-chip memory and external memory interfaces
Integrated MAC/baseband processors
Quality of Service management
I2S interface for high fidelity audio applications
On-chip low-dropout linear regulators for all internal supplies
Proprietary spurious-free clock generation architecture
Integrated WEP, TKIP, AES, and WAPI engines
Specification:
802.11 b/g/n
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Integrated TR switch, balun, LNA, power amplifier and matching network
Integrated PLLs, regulators, DCXO and power management units
+19.5dBm output power in 802.11b mode
Power down leakage current of <10uA
Integrated low power 32-bit CPU could be used as application processor
SDIO 1.1/2.0, SPI, UART
STBC, 1×1 MIMO, 2×1 MIMO
A-MPDU & A-MSDU aggregation & 0.4ms guard interval
Wake up and transmit packets in < 2ms
Standby power consumption of < 1.0mW (DTIM3)
Description
1. Support 802.11 B/G/N
2. Communicat
Description
1. Support 802.11 B/G/N
2. Communication range up to 100 yards depending on environment.
3. Standard 3.3VDC operation with 5V compatible I/O.
4. Standard 3 wire (TXD/RXD/GND) serial communication (idle high) at 115200/8/N/1.
5. Standard 0.1" (2.54mm) half through hole.
6. Upgradeable firmware.
7. Three mode of operations: Client/Access Point/Both Client and Access Point.
8. Support all major security schemes: OPEN/WEP/WPA_PSK/WPA2_PSK/WPA_WPA2_PSK.
9. Support both TCP and UDP communication.
10. Working as TCP/UPD server supports up to five (5) connections.
11. Working as station can connect up to 5 TCP/UPD servers. The ESP-04 can connect to all standard non-SSL websites in the world.
12. Simple AT commands for all operations.
13. Connection based data reception or transparent data reception.
14. Programmable client connection inactivity timeout.
15. Automatic domain name address resolution for public domain name but not the local name within the local area network (router).
Description:
1X(The ESP8266 is a chip highly designed fo
Description:
1X(The ESP8266 is a chip highly designed for the needs of a new connected world.
It offers a complete and self-contained Wi-Fi network solution, allowing you to either host the application or download all Wi-Fi network functions from another application processor.
Its high degree of integration on the chip allows minimal external circuitry, and the complete solution, including the input section module, is designed to occupy a minimum area of PCB.
Dimensions: 4 x 3 x 0.3 cm
Color: Blue; 100% New and high quality. This product is your best choice. Do not hesitate. It is time to replace your old, worn, damaged product.
Materials: CCL
Warnings:
This module requires a voltage supply of 3.3 for VCC, and 3.3V of logic.
Can not accept 5V.
Connecting the RX or TX over 5V Arduino will destroy this module.
You must use a logic level converter, or a 3.3V for Arduino
The supply of 3.3V on the Arduino Uno has an inadequate current capacity to power this module.
It must provide a separate power supply and higher than 3.3V (approximately 300mA or better)
Package includes:
1 x Wireless WiFi Remote Transducer Module ESP8266 Serial Esp-07 LWIP AP + STA
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.)
Features:
SDIO 2.0, SPI, UART , 32-pin QFN package , Int
Features:
SDIO 2.0, SPI, UART , 32-pin QFN package , Integrated RF switch, balun, 24dBm PA, DCXO, and PMU , Integrated RISC processor, on-chip memory and external memory interfaces , Integrated MAC/baseband processors , Quality of Service management
I2S interface for high fidelity audio applications , On-chip low-dropout linear regulators for all internal supplies , Proprietary spurious-free clock generation architecture , Integrated WEP, TKIP, AES, and WAPI engines Solutions
Specifications: 802.11 b/g/n , Wi-Fi Direct (P2P), soft-AP , Integrated TCP/IP protocol stack , Integrated TR switch, balun, LNA, power amplifier and matching network , Integrated PLLs, regulators, DCXO and power management units , +19.5dBm output power in 802.11b mode
Power down leakage current of <10uA , Integrated low power 32-bit CPU could be used as application processor , SDIO 1.1/2.0, SPI, UART , STBC, 1?1 MIMO, 2?1 MIMO , A-MPDU & A-MSDU aggregation & 0.4ms guard interval , Wake up and transmit packets in < 2ms , Standby power consumption of < 1.0mW (DTIM3)
Description:
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. , ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.
Overview:
ESP8266 is a highly integrated chip designed f
Overview:
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor.
Description:
Breakthrough design, there are new breakthroughs, based on ESP-12E.
The new four-layer board design.
The new revision antenna RF performance optimization, communication distance is increased by 30% -50% compared to ESP-12E!
Semi-hole chip technology, the whole IO leads, with metal shielding shell
Passed FCC & CE & RoHS certification
Built-board PCB antenna
4M bytes SPI Flash for programming.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area.
Features:
Standards Certification: FCC / CE / TELEC
Wireless standards: 802.11 b / g / n
Frequency range: 2.4GHz-2.5GHz (2400M-2483.5M)
Data interface: UART / HSPI / I2C / I2S / Ir Remote Contorl GPIO / PWM
Operating voltage: 3.0 ~ 3.6V (recommendation 3.3V)
Working Current: Average: 80mA
Operating temperature: -40 ° ~ 125 °
Storage temperature: Nomal temperatu
Selling unit: Single article Individual package size: 3X4X5 cm Weight per unit:0.5 kg Type of pac
Description The HC-12 is a 100mW multi-channel wireless transceiver you
Description The HC-12 is a 100mW multi-channel wireless transceiver you can use in your projects to transmit and receive serial information. The HC-12 is a half-duplex wireless serial communication module with 100 channels in the 433.4-473.0 MHz range that is capable of transmitting up to 1 km. This project will begin by using the HC-12 to create a wireless link between two computers and end with a second article that creates a simple wireless GPS tracker.
Isolated DC/DC Converters 5V/10A 9-36Vin 1/16brk -Log FLG BP
Overview:
Core51822 is a wireless module based on nRF518
Overview:
Core51822 is a wireless module based on nRF51822 - the Multiprotocol Bluetooth® 4.0 low energy/2.4 GHz RF SoC designed for ULP (ultra low power) wirelesss applications.
Core51822 Specifications
Onboard chip: nRF51822
Communication distance (open outdoor@1M data rate): 30m
Frequency range: 2.4GHz
Operating voltage: 2.0V ~ 3.6V
Operating temperature: -40℃ ~ 85℃
Dimension (PCB): 24.5mm x 32.26mm
Expansion pinheader: all the I/Os except P0.26 and P0.27
Pinheader pitch: 2.00mm
Spacing between pinheaders on the left side and the right side: 18.00mm
Antenna: onboard antenna
NRF51822 Features:
2.4 GHz multiprotocol RF transceiver
ARM® Cortex™-M0 32 bit processor
128 bit AES HW encryption
128kB flash & 16Kb RAM
Programmable Peripheral Interconnect (PPI)
Digital interfaces: SPI, I2C, UART
10 bit ADC
Programmable output power: -20 to +4 dBm
Independent application development and protocol stack
Fully compatible with NRF24L series
Pinout compatible with NRF51xxx series
Global separate power management
Operating voltage: 1.8 V ~ 3.6 V
Applications:
Wearable devices
Bluetooth intelligent application
Mobile phone accessories
RFID labels
Smart home appliances
Industry control
Data acquisition system
Revision History
2015.06, Core51822 upgrades the onboard chip to Rev3, features RAM 16K,
supports higher version SDK, and all the demo codes are still compatible with the Rev2 ones.
Package Include:
1 x Low Power Consumption BLE4.0 Bluetooth 2.4 GHz Wireless Module NRF51822
Brand new and high quality. Chip board ENC28J60-I/SO. The boa
Brand new and high quality. Chip board ENC28J60-I/SO. The board 25MHZ crystal. The network interface board HR911105A. 3.3 V supply pin. Debug reminder: 1, the IP address of the computer to a network segment and module such as IP module 192.168.1.2, IP computer set: 192.168.1.3; 192.168.1 is the 3 section; 2, the network cable connected to the mouth of the computer network module and mouth; (that is, the cable network 1 3,2 , and then do not understand that there are pictures Baidu); 3, the module and the MCU connection should pay attention to the connection of each line is reliable (the surface is not even connected to the good); 4, and the MCU port IO to confirm that is right; 5, the program recompile, download, confirm whether to download! STM32 and 51 IO size:48 x 18mm Material:plastic colour:blue Package Contents: 1 x Ethernet Shield Only the above package content, other products are not included. Note: Light and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.